I am so angry at this point because this shouldn’t be such a difficult issue. No matter what I do, I do not have a way to adjust scaling on documents I’m printing. Like you know when you want your doc to fit the width of the page or fit everything onto one page. I have no option to do this. It scales it how it wants even if a page is too wide and then it prints the left half on one page and the right half on another. I am so mad because I just switched back to macOS from windows and I had literally so many options to adjust the scaling when printing on my pc and now I want to cry (kidding but not really)
I am sorry if this is the wrong place to post this but I’ve googled and googled and googled and I cannot find a proper answer

Thanks for deciding to read my post today. This is not the definitive or complete explanation of wheelchair ramp design. Before I start let's get the technical potentially legal stuff out of the way first.
Ramps that are indoors or in a fenced in area like a back yard (THE FENCED AREA MAY BE DIFFERENT IF IT IS ACCESSIBLE TO THE PUBLIC). Ramps not used by the public = Food delivery, mailperson, utility meter reader, Jahova's Witnesses, etc.
These Ramps do not need to Meer ADA requirements. But should still be functional and safe to use. You'd be surprised at what people do. But if it works, then it works.
Backyards that are fenced in and not accessible to the public MIGHT be excluded.
FOR ANY RAMP OR ACCESSIBLE FEATURE ADDED TO OITDOOR SPACES THAT THE PUBLIC CAN ACCESS WILL 100% NEED A TOWN OR CITY PERMIT. THIS IS WITHOUT EXCEPTION.
Here is where it gets real. If you decide to ignore this and say someone trips, slips pr otherwise gets injured by your accessibility fearure. YOU and only YOU are at fault. Even if it is 100% ADA compliant, the feature was not properly registered with the town or city so it can be noted when and where it is installed and on what property.
Next the town or city will fine you a set amount per day it was in place without a permit. For example a permit for my handcycle shed cost $100 that might seem unfair and costly. But if I had just built my shed without permit they could fine me $1,000 per day it was up from the time it was built.
Getting a permit and making things 100% or better than ADA complaint, yes it is easy to surpass what the ADA asks for. ADA is the bare minimum expected.
This doesn't mean someone trying to con you won't try and sue you. But, if you have things in order such as getting a permit. Making things at least ADA compliant will support your side in a legal issue.
Yup that is the borish stuff for the most part. Forget about it and life will likely get very annoying.
For those who are interested and want a live community to chillax in to talk about most anything really, listen to music and make requests for Fave songs or topics you would like to discuss.
I broadcast live typically in the cold months M-F from around when my pain allows me to get up varies 9am to after noon and I go until my sweetheart arrives home. About 5PM to 6PM I have been broadcasting live 16 years.
Quite literally I am just repeating here what I will talk about live also.
TikTok until the ban kicks in. Then it's back to Twitch. AbiliTV or AbiliTV Live. If you Google the name do not pay attention to the website I don't have one. And the owner of that sight well let's say I don't endorse him.
I am on YouTube, FB, IG,,Twitch, account still there but not used since it went to X (Twitter), Kick - although I don't like the vibe on Kick.
Of course I am here getting started here on Reddit in a more text based community. I am in the Wheelchair and Disabilities communities where I am learning about all sorts of amazing people.
OK, I always hate posting I am a live content creator. I hate it so much I have hardly any community live.
Ramps.
What makes a crappy, good, or excellent ramp?
For me it is the little details that really make the differences. I will use images to try and explain the bare basics.
1st image: Most people see this and think: My prayers have been answered.
No they have not. You will notice the direction the person is using the ramp. Manufacturers do this to play into your desperate need for a ramp solution. They want you imagining how easy there ramp is to use. So they stage images showing that. Much how homes are staged. To make it easier for people to fall victim to slick sales tricks.
What if the door were closed and rhe person was approaching the door? Look at the ramp. How does one say open s screen door or storm door that swings out? Most dwellings will have one.
Now imagine it's raining really hard and that nice metal surface isn't as grippy? And you have a bag or two of groceries on your lap. Now open the storm door and then before it closes as they are typically on a door closer of some design. As you fight the storm door, are annoyed by the driving rain, and fumbling for your keys.
Even on an ideally perfect day without snow or rain this ramp will work 100% against you. Also it isn't wide enough to allow you to move over out of the way ofcthe storm door. Meaning you need to back up and get the door perched against your wheelchair frame to now roll foward to open the entry door. Sadly using the wheelchair brakes just make things all that much more frustrating.
2nd Image: 3 ft ramp $219. This seems decent right? It isn't. You have to account for the pitch or slope.
If you have a threshold that is 10 inches higher than the surface you need to reach, this means you need not just a ten foot long ramp but a raised area that meets the threshold that the ramp attaches to closest to the surface you're trying to reach.
What happens if you decide to use a short ramp and have a steeper slope? The worst will be to flip backwards going up. Next worst you don't have the upper body strength to make it. The next will be you deciding never to use it except to exit with. It is a little less scary going down. Although you need really good hand strength and dexterity to maintain control at higher speeds.
ADDING INFO AS A SAFETY REMINDER: Most manual wheelchairs have what are called brakes. ⚠️ ⚠️ ⚠️ These are NOT brakes like those of a car, or bicycle. Injury or worse can happen when they are used as friction brakes. DANGER: You risk not only destroying your tire and wheelchair but also injuries from catastrophic failures of the tire and possibly the rims of the wheels.
These levers no matter if they are push or pull to lock or scissor styled brakes are only meant and made to hold you in place AFTER you use your hands to stop with. OR FEET for those able to do that.
The reason these are not brakes in the typical sense is because of how they work. They bite into the tire material and can blow out air filled tires by ripping through the rubber tire. On solid tires they can tear the tire causing it to fail and possibly fall off the rim. If the rim is left exposed and you are moving the metal or composite rim will slide on the surface.
The biggest excuses I hear for using these levers as brakes are: They are called brakes. YouTube wheelchair brake basics how to use and not use them. I don't want people ending more disabled than they already are.
My hands are to weak to stop me. I understand that. So my best suggestion is rubber coated work gooves. Leather gloves or some form of glove that you like to use. I personally don't like wearing gloves, but when I go on 16 mile strolls I wear a pair. They provide additional traction and that grip means less hand strength is needed to stop overall. It is not recommended to grab the tire for additional friction at any time while moving down hill.
If tire use us needed make sure you have a pair of heavy duty leather gloves on. Welding gloves short gauntlet works. Warning: This method destroys gloves rapidly. These is due to the sandpaper like friction the tire creates with its texture and tread design. Extreme heat can build up and burn your hands. So pay attention and release grip changing hand positions to reduce this.
Ramps have to be designed to work with the fact wheels like to roll. And steep ramps are what prompted my warning about brake use.
I am considering designing a brake system to work like a bicycle that could be added by most people. I will look into this concept at some point.
So a stubby short ramp might be low cost but isn't the answer it appears in most manufacturers images.
Lots of information that needs to be shared because so many people will fall into the thinking what they have is a good solution and it's harming them and the equipment they use.
Good news here: Most towns and cities do not charge or keep the charge very low for ramp and other disability access devices in public spaces.
What the permit does is show you the bare minimum of what is required to make your project ADA compliant. Also it resistors your ramp or lift with the town or city and at what property. This way should a nosy neighbor want to whine about your project looking horrible the town or city can reassure that negative rube that you are in full compliance with all the ordinances and ADA requirements. So they can mind their own beeswax.
Also the permit is a must if a property owner or landlord are to allow the access in the first place. This has to do with liability and property insurance. Speaking of that crap it would be wise to invest in renters insurance in the event someone claimsxto have been injured by your device. Do not depend only on the landlord or property owner's word that its covered. You could also ask your town or city how that works also to get a straight answer. If the landlord or property owner does claim you are covered always get that in writing.
3rd image shows the lack of what is called a staging area. This is exactly what a porch does. Notice the porch is flat and provides room to move out of the way of any storm door? This is a super important and all to easy to miss feature that makes a ramp go from frustrating to awesome.
I even made that mistake with my ramp I built for my garage. I did change it so it has a 6ft deep 4ft wide same as the ramp staging area that once I installed a screen door I use daily.
4th image: Now it gets colorful. Nothing attaches to the porch or the building in my design. This is to respect the property. And save you on extra costs to restore things later.
The support for the flat area of the porch:
Measure uo to the front top edge of the threshold. Say this is 6 inches or so... Using 4X4 cut to the same width of the porch. These are rated for outdoor ground contact.
Next using decking wood this should be equal to the top front edge of the threshold. In effect the timbers are the support they are orange and just on top of the porch. They go across to provide full support.
How to determine how many. For the porch shown in your image would likely use three. One right under the threshold, one in the middle, and one right along the front edge of the porch.
Decking would go left to right and for the parts with out full support use scrap pieces of 4X4 to position under those rows.
An alternative way to set the supports are: under the threshold is left to right full width of porch. Then instead of the others being left to right. Place one on the left going vertical or not left to right. One on the right side going perpendicular to fhe horizontal one. Then you will cut one 4 inches short for the center also placed parallel to the left and right. The front porch edge piece cut to fit the width between the left and right support.
That would allow you to place decking horizontally left to right with out worry of adding support for some of the deck strips.
The front edge of porch part I feel should be left to right mainly to insure there is no possible way for a ramp to flext or bow in this area. But you are welcome to Google methods on building something like this also.
The ramp for the porch will be the longest most likely based on the photos you shared. They are also referenced later in my post.
Only around the porch and the outside of the caster wheel guides on each side or the blue color in my image needs a railing, as well as down that first ramp.
The other ramps are little more than the plywood laying there. You wouldn't even really need the blue guides on the but they add additional stiffness from bouncing and bending.
Again Google is very good for finding examples of how you can design a capable railing. It doesn't need to be fancy, just meet the requirements the ADA sets. To avoid annoying splinters I strongly suggest using iron pipe or proper outdoor rated round railingbars.
Benefit of the metal pipe is it is very low cost. Con is in the sun it can get hot. To overcome thar railing grip tape can he used to cancle out the hot part and make it easier to grasp. Grip tape is not required.
Thankfully all of this is pretty easy to do if you have some some basic tools or have access to them like narrowing them. If you lack the skill or ability to do this. Trust me when I say buying lunch each day for the hard worker(s) often is payment enough. And Thank You is the perfect payment. Our reward is seeing you enjoying the work put into the project.
Last there is an green outline of a 2x4 on each side of the porch staging area. Put one on the far side as well and this should keep the staging area from shifting leftcand right. Surfaces endure a lot more force than we realize.
5th image I used my garage ramp before I corrected the flat staging area issue.
So this isn't how my indoor ramp now looks. It has no railings as it is not required and the flat area towards the garage side has a 4 inch tall wheel guard wall to keep me from accidentally rolling off front casters or rear wheels.
But, this is roughly how your front porch would look like. All designed to keep everyone safe who uses it.
By connecting the ramp to the flat staging areas makes it much harder for it to shift around. In the case of this if you owned the property you would use a contractors grade waterproof glue and 4 8 inch long lag bolts to secure the 4x4 or wood support right next to and under the threshold and bolt it and glue it to the location. Silicone sealant works also as it is mainly to keep insects from making the area home.
But since the property needs to be returned to original state, I find that making a saddle staging area works wonders. Sadlle in that it is,like a horse saddle. It isn't bolted to the horse but does use the shape of the horse as the stabilizer. And is easy to remove when needed.
Image 6: Sorry about the messy drawing. This is your photo.
The green is the railing around the porch and the first longest ramp.
The light kind of red horizontal strips are stair tread grip tape. Using wood screws shorter than the thickness of the plywood allows you to have a 2 method way to keep these strips in place. For how much they cost you will thank me. One screw near each corner and two one top one bottom in the center. This insures they are secure. The gue or adhesive isn't likely going to stick in every case.
You want full left to right coverage with 2 to 3 inch spacing between each horizontal strip. Yes you can just apply them centered and hope no one slips of they walk closer to the railing. Plus it makes insurance companies feel better also with more safety in mind.
In the event someone slips or falls when pictures are taken of l the scene it will look better for you to have provided more safety than not.
Also more screws can be used if desired. The only thing to make sure of is all screw heads are flat to the surface. The two method way also known as redundant measures to make sure things don't fail to the point of a catastrophe.
The ADA will likely have other suggestions different than I mention. Either will work, I find much of my ideas go beyond ADA requirements.
The ramps since they are so minor in slope may even be able to lay strips of 2x4 or even 1x1 that you screw to the underside of ramp. I almost think you could make what would look like a continuous ramp.
One step won't really need all 8 ft of plywood however keeping them full length means you could likely add smaller pieces where one ramp ends to meet with the highest point so you can connect them so this keeps them from shifting and moving as they will.
The little green marks along the sides of the blue for the length of the ramp represent side supports that are rounded into the ground and screwed to the sides.
As you use a ramp that is not secured it will move a little in the opposite direction of your direction of travel.
Also it will shift left or right when you first roll onto it. And since the ground shown is easy to return to its original condition once this is removed lowers cost at that time.
The blue dots represent horizontal srips placed where needed these are screwed in place as yes they will slide and move into new positions that don't support the ramp.
The goal is no bouncing, bending, flexing, warping ramps.
As long as all wood is rated for ground contact otherwise it will rot away pretty quickly otherwise.
The blue kind of bloody areas are flat sections filled in with plywood.
So once you enter this ramp ot remains a plywood surface until the porch area. Where it's decking.
7th image: An example of how your ramp could be designed. In this image since the ramp os longer and rises up higher I definitely would include ratings on each side. But - it may not require them so that is OK also. The redish area is a flat area at least 5 ft deep and 4ft wide. This would allow a person the chance to turn around also.
The circled spots denote support placement.
Now your steps for me would not need a ramp as I can strong arm my way up short steps or curbs like those. Tha porch would be the only area I would build if this were my place.
8th image: Immediately after moving in I built this and prior to finding the original screen door that the price owners removed and I reinstalled.
It was no fun using this ramp when I had to open the door. I typically had one of the kiddos now all grown up open it first for me.
The lack of a staging or flat area is a huge mistake.
This is ground contact outdoor rated plywood nearly 1 inch thick. Plywood keeps the construction simpler, and removal easier also later.
9th image: Shows the outdoor ramp. Notice the grip tape on this. This is the typical arrangement. I suggest side to side full width strips so able people can walk anyplace and be assured solid footing. The spacing I prefer also assures wheelchair tires have solid grip.
The steeper the ramp I say 3 inches between horizontal strips.
The shallower ramps for your lower or step ramps can be 4 to five inches between them. If they are wide strips works better.
Image 10: This is the ADA recommendation: 36 inches wide. Trust me especially for entry doors you want some space to move over to the side to get out of the way of a screen or storm door. And a place to put down groceries or a package or anything else so you can access the door.
48 inches just happens to be a pretty decent and better than ADA requirements that allows you more room for any purposes.
Image 11: Shows your porch. From what I see this should be pretty easy to cover with the staging area over the porch and ramp going down.
You want to measure from the front edge ofcthe threshold to the ground in front of the porch the walkway leading to it. This will give you a total height that needs to be accounted for.
Say it is a total of 10 inches tall. Your ramp will be 1 foot out per one inch in height. So 10 feet long. Now say you have the room and used 2 8 foot long plywood sheets end to end that is 16 ft. That means your slope will be less overall and easy to roll up. 10 ft will be usable but will be a little harder to roll up.
Funny thing is you use the same energy to roll up 10ft or 16ft. You just exert less energy over a longer distance that still equals the amount it takes to go up a 10 foot length.
Slope is something only you know what works for you. So if you need a little longer of a ramp if room allows it then that is fine.
Oh I forgot skip over the smaller step when making your measurements. That isn't where a ramp will end at to rest.
Image 12: The walkway. These little steps are easily rolled up by some wheelchair users. However of you can not. That is fine.
The over all length of these looks decently long enough. You in effect are just governing them as I hope I explained.
To keep the ramps from moving side spikes can be placed as mentioned 2 at the sides and top, two in the middle sides. And 2 and the bottom sides.
They get rounded into the ground next to each area of the Ramos they will be screwed to. You might even be able to lay a plywood sheet down and see if that is enough to raise you up enough. That the plywood could just lay on the walkway.
Now most likely that option will not fully work. Offered as an alternative.
The very end where ramp ends or starts at the lowest point you can get an aluminum door threshold commercial grade one. It means a little bump up onto the ramp and or down it.
I will photograph the one I have as it works like a charm. Also the rest of my garage ramp.
The deck to ramp can be connected using lag bolts from underneath into the 2 4x4 support. Using 6 or preferred 7 or 8 inch long lag bolts 3 of them to secure the ramp to the staging deck area.
Trust me when I say this, this is a mere drop in the bucket of information on how to design a ramp system.
Last little note:
Always get a permit prior making anything. The permit should cost nothing or very little since it is an accessibility ♿️ need. The information the permit comes with will also be of huge help in DIY or other options.
Sadly there is no way to construct something like this for no cost. However, church groups, friends, local elected officials, and others can be great resources. From fundraising, to helping you locate a foundation or charity to help cover some or all of it.
Do not feel bad for asking for help like this and when needed. Being a renter doesn't mean you should not have accessibility.
Like I mentioned if I was your fellow disabled neighbor I would help construct this.
Tools needed:
Tape measure x 2 I always end up needing 2 of them at times.
4 ft level.
Carpenter square.
Torpedo level. This is a 1 foot long smaller level like the larger 4ft one.
Carpenter or construction style pencil ✏️ they are flat and don't roll away when sat down.
Wood/deck screws 3 or 4in long.
Cordless drill and 2 batteries allows rotation of them when charging. They typically will last 2 or hours each. So when one runs out charge it while using the other.
Leather work gloves.
Socket wrench set for lag bolts.
Screw driver set. Mainly a number 2 Phillips and flathead. These come in handy.
Circular saw - they come corded or cordless either works.
Hand saw for those cuts to awkward for a power tool.
Drill bits for pre drilling holes.
Liquid nails to glue some things together.
Short wood screws not longer than the plywood is thick. For the grip tape strips.
Safety glasses get a few pair.
Hearing protection. Cutting wood can be really loud. Same with drilling it and all.
Things that could help: Something stable to place wood to be cut on.
Saw horses or milk crates the sturdy plastic ones. If they get cut into no big deal.
They cut be cut safely on the ground without risk of damaging tools or injuring you.
Since we are all in the same boat 🚢 in many respects, I find it sp satisfying helping people by helping them learn how they can also help themselves. It's how I was raised. Knowing you have some information and know where to locate more is my payment.
Back to me talking about my live content.
A lot like this post and my others, it is insanely boring stuff. 😴
However, I ask what other content creator is willing to discuss and cover this type of stuff?
Really go look on Twitch live, YouTube live, TikTok Live, Kick,Instagram Live or any other site allowing live content.
How many do you find that can answer questions or get you aimed in the correct direction for the information you need?
16 years now this is what I do for free. I will not and do not monetize my content. I removed myself from Twitch affiliate orogram, I have asked TikTok to allow offboarding and the option to not monetize.
I prefer to lead by example.
Please consider getting to know this strange goofball of a weirdo on my social media channels. It's not a big community but any means and is well sp unique that most people fail to realize all the nerdy disability related bits of knowledge I have to share. Plus I love light sabers and anime to make me extra geeky.
AbiliTV and AbiliTV Live on the main social media platforms.
On TikTok my actual username is AbiliTV and my screen or showing name is DJ Wheelchairbeats.
If you visit tell me your from Reddit and I will in a very socially awkward way greet you. Well I hope with practice this gets less awkward in time. :)
I am not seeking a relationship. Or any side quests. I am at level 54 in my life and to old to give a fart for drama. Making cool new friends, now that's what it's about.
Time to get some photos of my garage ramp.

Hello! I’m looking to have a character designs. Looking for something flat colored, and either a single fullbody of the design or a reference sheet.
I am looking for someone who can come close to or mimic the Steven Universe style, specifically the style of spinel! References included are so you can get a gist of the style I’m looking for.
Discord or twitter preferred for communication. Please leave a comment down below! I don’t tend to check DMs. It would be lovely if you left your discord or twitter down with your comment.
Payment will be supplied through Paypal, Cashapp, or Kofi. Can adapt to other services.
Budget is between $60 and $100.

I’ve always loved this colorful/thrown together style, but I cannot imagine a way to achieve it with the bed set I currently have(the first pic). Does anyone have any suggestions of what blankets/sheets/pillows the combine it with? Pics welcome!

(Look at images attached)
I’m at my wit’s end. I come to this sub time and time again with the same issue and nothing ever sticks.
I’m trying to print out essentially the equivalent of laser-cut cardstock, so the final result is supposed to be a sheet of cut-out paper if that helps for any visualization.
After switching to a different color filament (PLA), I am having lots of issues. I seem to have resolved all but the main issue. The filament is being worn down in the extruder and stops progressing. I upgraded the Bowden tube and switched to a metal extruder, and it made no difference at all. I replaced the nozzle for good measure. Bed is level. Fan is fine. No heat creep. There are no clogs. The issue is in the extruder or the software.
I read that the stock extruder spring may work better, so I switched the spring to the old one. The extruder is no longer clicking, but it still stops progressing after a couple layers. I loosened the spring tension. Didn’t work. I removed the little stopper thing in the spring, didn’t work. I’ve calibrated e-steps countless times as well.
Other things I have done just for more information: Temp is 210 Speed is 70 Bed is 60 I’ve already tried tightening/loosening belts
The skirt prints perfectly fine, as well as the first layer. After the first layer is when it stops extruding because the filament is stripped in the gears.
I changed my extrusion settings in Cura, I tried turning off extrusion entirely (it seemed to work but it was messy), I changed the maximum retraction count to 10 and the minimum extrusion distance window to 2. I also tried 20 and 5, respectively. Also messed with retraction speed and distance slightly to no avail.
I’m ready to throw this thing in the trash. What now?

I present you, my second keyboard project, and my first full custom project: the mikefive. If you like, read below how it came to be and more details about the build.
https://preview.redd.it/9ze3tggr1axc1.jpg?width=4096&format=pjpg&auto=webp&s=d58455d5912634e81660870740edf206309f01cd
The first keyboard project was a typeractive wireless Corne which I built about a year ago. After typing 6-finger-qwerty for my whole 38-year life, I switched to ortho, split, colemak-dh, blank keycaps, learned to touch type, and never looked back. However, I found that I was always orienting the Corne halves the same way and started thinking about an unibody.
A friend from work liked my 'alternative' keyboard and wanted to build something too. I showed him the rabbit hole including switch options and also showed him the Kailh X (PG1425) switches. These, and especially the keycaps, were hard to come by but we liked the idea of a slim keyboard, so we decided to email Kailh directly. To our surprise, we could order X switches and caps directly from them, although there was a somewhat high MOQ (minimum order quantity). So, him, me and my friends’ housemate decided to order together.
But Kailh suddenly said: “Are you also interested in these PG1316 switches?”. I never heard of those, but the spec sheet they sent looked interesting: tactile, even lower than the X switches, and completely surface mounted on PCB. Officially, these are laptop switches. But hey, potentially this could become something really slim. So we decided to order a sample batch of these too.
My friend continued his design for the X switches and Chocs (PG1350), but when the Kailh box arrived, and I saw and felt the PG1316’s, I knew I wanted to build a keeb with those. I learned to make PCB’s with help from Joe Scotto’s YouTube video and KiCad library, and the same friend who happens to be a mechatronic engineer. I am an industrial product design engineer, so I know my way around 3D CAD and product design.
And, here we are. The mikefive, which gets its name from, well.. me, and its complete thickness of 5mm. Including the keycap, the switch stands 4.2mm tall and is mounted on a 0.8mm thick PCB, making a total of 5mm. The switch has a travel of 1.8mm, and magically disappears completely inside the keycap volume when pressed. In the picture below you can see how thin it is, compared to my Corne with Chocs.
https://preview.redd.it/66j1j9eu1axc1.jpg?width=4096&format=pjpg&auto=webp&s=0557230fe08dd332c5db38998175a5e4eaf11e5c
Because the switch is surface mounted there are no solder pins sticking through the PCB and the PCB can be safely used as a bottom plate without exposing any contacts.
Kailh was nice enough to send the 3D CAD files of the switch and cap so I could use it for checking the fit in KiCad as well as make some nice renders to make design choices a bit easier. Here is a render of the final design before I ordered. Note how I made the bottom edge of the housing near the thumb clusters a little lower then the other edges so the user thumbs will not interfere with the edge there.
https://preview.redd.it/2gvasd483axc1.jpg?width=2000&format=pjpg&auto=webp&s=d930be16c29b186335aec58fa102e9704c0bd364
I chose a 17x17mm spacing, sometimes referred to as CFX spacing. This is 1mm narrower than the 18x17mm Choc spacing I was used too. The choice was primarily based on the square PG1316 keycaps, because I dislike unequal spacing between keycaps. I 3D printed a mockup and the CFX spacing felt very workable, so I went with it. The PCB’s and the CNC’ed aluminum housing are both from JLC. I did some splatter artwork on the back of the PCB including an isolated solder pad in the shape of the logo.
https://preview.redd.it/0qy7iolv1axc1.jpg?width=4096&format=pjpg&auto=webp&s=da29fdd8a83da84a3c320a6f437128f7e731c69c
Soldering was done all using a Miniware hotplate and solderpaste we have at work. It is impossible to solder the PG1316 switches by iron, because the contacts are located underneath the switch. Four larger contacts on the corners of the switch lock the switch its ‘frame’ to the PCB by solder. I placed vias in these corner pads for a more secure connection to the PCB. Because the hotplate is small, it took some time to solder everything, but is was easy and I enjoyed getting closer to testing it.
https://preview.redd.it/y7501i0x1axc1.jpg?width=4096&format=pjpg&auto=webp&s=8ad295892ab851c8954841c170b138c44c8c6d34
Despite being the thinnest switches I have seen, there is space underneath the switch for a backlight LED, which I did not place. Instead, I used this space for the 1N4148W diodes in SOD-123 package. Soldering with a hotplate is easy and magical as the tiny components magically align by themselves. There is also a popular MSK12C02 power switch to disconnect the battery. The diodes, switch and controller were ordered from splitkb, which is in my tiny country. Bedankt voor de stroopwafeltjes Thomas 😉
https://preview.redd.it/entjmv1z1axc1.jpg?width=4096&format=pjpg&auto=webp&s=19049b31d1d8361db849ba786e10449256571b3a
Next to the extremely low profile switches I also needed to fit a controller and battery. Luckily, my typeractive Corne already showed me the right parts with the super thin nicenanov2 and the 301230 battery that both max out below 3mm. I never saw a through-hole controller mounted flush like this but using the hotplate the soldering was a breeze. I made some small additional pads next to the controller pads (you can see them on the picture above) to check if all the individual pads were connected well using a multimeter.
To my surprise, my first time designing a PCB, first time hotplate soldering, first time making a custom shield in ZMK, everything worked! It was a question whether there would still be a good Bluetooth connection with the metal housing covering the whole center controller, but everything just works perfectly. During PCB design, I removed the ground planes on the PCB locally where the Bluetooth antenna of the nicenano is, and the controller being so close to the bottom probably helps for getting out the radio waves through the bottom.
https://preview.redd.it/rkd3bdy02axc1.jpg?width=4096&format=pjpg&auto=webp&s=fce3fbc1d6c9e468e998e1d5dbd27c77e85263a4
I wanted the case to add as minimal as possible to the keyboard. I primarily wanted the case to stiffen up the relatively thin PCB and protect the surface mounted switches from side impact, when for example dropping it into my bag. That is also why the ‘holes’ are in the keeb, to make the contour is smooth for easy into-backpack-sliding. Each half is at 15 degrees, so 30 degrees total between halves. I experimented with this angle using my Corne and liked it this way. The center piece is as small as it can be for housing of the controller and battery.
https://preview.redd.it/5ywdcgm22axc1.jpg?width=4096&format=pjpg&auto=webp&s=6d84d58cbac9ad3dc291c85a2527aa9460e8e754
The Kailh provided keycaps are transparent, and have the letters A, B, C and D on them from the inside. Probably mold marking from production. I guess these would be painted when used in laptops, and transparent to the light passes through. I decided on the white PCB color and natural aluminum housing to match the current switch appearance a bit.
https://preview.redd.it/loyify842axc1.jpg?width=4096&format=pjpg&auto=webp&s=7a31ce7af3c9a17f5dd104ed45f1f9c7135ae748
There is one slight flaw, and that is that the PCB slightly warped during all of the hotplate soldering from one side. Therefore you can see it lifts slightly out of the housing at the bottom edge. Unfortunately, I did not put a screw there to hold it in place, like I did on each corner and in the middle using countersunk M2x3 torx screws. Yes, I did some manual countersinking using a countersinking drill bit in a 0.8mm PCB to make the bottom fully flat. I made sure to have no copper ground planes around the PCB holes to make countersinking easy, and it was.
So, how does it type? Well, the first thing I noticed, coming from Choc Red (linear 50g), it that PG1316’s are very tactile and very strong. I also have all the tactile Chocs sampled here, but nothing comes close the tactile bump in these. The spec sheet says 60g tactile force and 32g operation force, but actually I question those values. I am getting more used to it as I work with it more, but I think it is still a bit heavy for my taste. I emailed Kailh about my experience, so I am curious what they will say.
But then, the height. It is so comfortable, its incredible. Even with the low profile chocs I had some strain on longer sessions. But this, is incredible. No strain at all. It is like tapping the table surface.
And then there is the portability. This thing is slimmer than your phone or tablet. It slides into you backpack tablet compartment with ease. It is also very light. The case is aluminum, but is all very thin so it weighs nothing.
I am excited about it, and will keep you updated on revisions and such. I can share gerbers and stuff if people want it. Let me know in the comments or send me a message.

​
April 28th is... National Superhero Day
-- Batman, Superman, Captain America, Wonder Woman, Iron Man, Hulk, Spiderman, and many more are who we think of when we think about superheroes. Even if fictional, they are great role models for children. Superheroes serve and protect while fighting against evil. Real-life superheroes may not have superpowers or wear capes but are also great role models. Military personnel, healthcare providers, police officers, firefighters, and teachers are just a few of the heroes we meet daily.

Free Printables, Coloring Pages, Activities, and Crafts:

🦸‍♂️ Superhero Connect the Dots printable worksheets
🦸‍♂️ Superhero Color by Number
🦸‍♂️ 37+ Coloring Pages Superheroes Printables
🦸‍♂️ FREE Online Superhero Comic Books
🦸‍♂️ 50+ Superhero Crafts
🦸‍♂️ Superhero Free Stencil Gallery
🦸‍♂️ Free Printable Wonder Woman Water Bottle Labels
🦸‍♂️ Superheroes Word Search Printable for Kids - Thrifty Mommas
🦸‍♂️ Superhero Database Superheroes, Villains, Battles, Teams and Superpowers
🦸‍♂️ Scout Superheroes
🦸‍♂️ Free DC Comic Printables and Worksheets
🦸‍♂️ Free Printables Invitation DC Super Hero Girls
🦸‍♂️ 18 DC Super Hero Girls Coloring Pages
🦸‍♂️ 22 DC Super Hero Girls Coloring Pages
🦸‍♂️ Super Heroes coloring pages
🦸‍♂️ Free Printable DC Super Hero Girls Bingo
🦸‍♂️ Superhero Girl Birthday Party Ideas and Free Printables
🦸‍♂️ Cubee - Superman Justice League
🦸‍♂️ Justice League: War - Life-Size Batman Helmet
🦸‍♂️ Free Superhero Clipart Images
🦸‍♂️ Superman Free Printable Original Nuggets Wrappers
🦸‍♂️ Zen Superhero Party - Craft Page
🦸‍♂️ Justice League coloring pages
🦸‍♂️ Justice League Character Turnarounds
🦸‍♂️ Justice League coloring pages
🦸‍♂️ Justice League logos coloring pages
🦸‍♂️ Superhero Printables
🦸‍♂️ 17 Super Girl and Superhero Parties Printables
🦸‍♂️ Grant's Superhero Birthday Party Printables
🦸‍♂️ Free Marvel Superhero online games for kids
🦸‍♂️ Marvel Avengers coloring page
🦸‍♂️ Marvel's The Avengers coloring pages Free Coloring Pages
🦸‍♂️ Marvel: Coloring pages, Free Online Games, Videos for kids
🦸‍♂️ Coloring Pages Funko Pop Marvel
🦸‍♂️ Avengers Age of Ultron Coloring Sheets - My Boys and Their Toys
🦸‍♂️ Marvel Coloring Pages for Adults
🦸‍♂️ Superhero Printables
🦸‍♂️ LEGO® Marvel™ Super Heroes - Videos
🦸‍♂️ Marvel SuperHeroes Free Papercrafts
🦸‍♂️ Marvel Comics Cubeecraft - Free Papercraft Toys
🦸‍♂️ Superheroes Make for Amazing Class Activities

Superhero Recipes:

🦸‍♂️ 35 Superhero Food Ideas To Make You Feel Like Super Mom!
🦸‍♂️ Simple Superhero Party Food Ideas You Can Make In Minutes
🦸‍♂️ Spider-Man Superhero Recipes
🦸‍♂️ 14 Adventurous Superhero Recipes - The Shirley Journey
🦸‍♂️ 25 Superhero Food Ideas that Don’t Require Super Powers to Make
🦸‍♂️ Fun and nutritious kid's recipes inspired by the heroes of the big screen
🦸‍♂️ Superhero Slime Recipe in Two Minutes Flat
--
More: April 28th Special Days - Featuring Superhero Freebies!

TLDR: Why do all my black background photos end up out of focus/over or under exposed/ otherwise bad despite varied attempts? I have tried for years to take good mini photos with that “inky black background” look that so many people use. Plenty of people have told me a black piece of something and lowering exposure on an iPhone will get you a perfectly serviceable one. Never worked for me. I’ve also followed tutorials (sometimes with seemingly contradictory suggestions) and done more elaborate light box setups, with many variants in placement, light source, distances in mini, camera, light source etc. The mini ends up out of focus, or the background is super grey and textured, light colored minis glow, etc. I hear people suggest using an app to adjust settings manually, but I’ve never found one I could navigate to anything like usable results. I have managed some of what I think of as pretty decent photos in front of a sheet of computer paper, admittedly trying to do more elaborate/expensive setups somehow usually yields worse results. Does doing more than printer paper just require a level of photo app and editing skill that’s way beyond what I’ve been able to teach myself? Is there something obvious I am missing? Does anybody have particular tutorials or apps and settings they might suggest? I have attached some photos to give an idea of one of thesetup variants I have tried, plus some examples of “white computer paper cheapos” that somehow come out better. Any suggestions and CC would be appreciated.